العودة إلى المدونة
نصائح والعناية 2026-11-17 Rollei 7 مشاهدة

F:X Pro Mark II Magnetic Round Filters: End Cap and Handling

F:X Pro Mark II Magnetic Round Filters: End Cap and Handling

The F:X Pro Mark II End Cap protects your stacked magnetic round filters in transit. Here's how it fits, which sizes exist, and how to handle the filters cleanly.

What the end cap actually does

The F:X Pro Magnetic End Cap Mark II is a transport accessory for the F:X Pro Magnetic Round Filters Mark II. It is not a lens attachment: it does not mount on the camera. Its job is to close the front of a stack of filters so the stack stays together and the glass is covered while it is packed away.

That distinction matters for how you use it. You stack the round filters on top of each other, and the magnets in the filter rings hold them together. The end cap then sits on top of the stack, held by the same magnets, and can also adhere to the closing base ring or step-up ring. When you are ready to shoot, you pull the cap off and put the filters on the lens.

End cap sizes and what the record confirms

  • F:X Pro Magnetische Rundfilter Mark II - Endkappe: The F:X Pro Magnetic End Cap Mark II is available in 62, 67, 72, 77 and 82 mm diameters. The cap size has to match the filter diameter you use, so check your filter size before ordering rather than assuming one cap fits every stack.
    F:X Pro Magnetische Rundfilter Mark II - Endkappe
    F:X Pro Magnetische Rundfilter Mark II - Endkappe
  • F:X Pro Magnetische Rundfilter Mark II - Endkappe: The end cap is designed to close a stack of F:X Pro Magnetic Round Filters Mark II and is held by magnets either on the filters or on the closing base ring or step-up ring. This tells you what the cap is for: keeping a filter stack together in transit, not mounting filters to the lens.
  • F:X Pro Magnetische Rundfilter Mark II - Endkappe: The end cap is not attached to the lens; it protects the filter during transport. If you expected a lens-mounted cap, this clarifies the accessory's role before you buy.

Closing a filter stack for transport

The supplied product information describes the sequence in general terms. Treat these as the supported steps, not as a full handling manual.

  1. Stack the filters: Place the F:X Pro Magnetic Round Filters Mark II on top of each other as a stack. The magnets in the filter rings hold them together.
  2. Seat the end cap: Place the F:X Pro Magnetic End Cap Mark II on the end of the stack. It adheres magnetically to the filters, or to the closing base ring or step-up ring.
  3. Carry the closed stack: The cap covers the end of the stack for transport. The record does not describe a case, pouch or drop protection, so treat the cap as protection for the filter face, not as a rugged travel container.
  4. Remove the cap to shoot: Pull the end cap off, then place the filters on the lens as usual.

End cap versus front cap: don't mix them up

The supplied information names two different accessories. The end cap closes the stack for transport. To close the filters at the front, the F:X Pro Magnetic Front Cap Mark II is needed. If your goal is to leave a filter on the lens and cap it there, the end cap is the wrong part; it is made for the stacked, off-camera state.

This is also why the end cap should not be forced onto a lens thread. The record states plainly that it is not attached to the lens. If a cap does not sit flush on your stack, check that you are using the matching diameter and the Mark II filter system rather than adding force.

Handling habits that keep round filters clean

The supplied record does not include a cleaning procedure, so the points below stay within what the product information supports: keeping the cap on, handling by the rings, and storing the stack closed.

  • Cap the stack before it goes in the bag: The end cap's stated purpose is to close and protect the filters during transport. Putting it on before packing is the supported habit.
  • Handle the filter rings, not the glass: The magnetic hold comes from the filter rings. Gripping the rings when separating or stacking filters keeps fingers away from the optical surface.
  • Keep the stack together: Because the filters hold to each other magnetically, a closed stack is easier to manage than loose filters rolling around a compartment.
  • Check the diameter before ordering: With 62, 67, 72, 77 and 82 mm options, the right cap is the one that matches your filter size. The record does not confirm cross-size compatibility.

What the supplied information does not cover

The record does not describe a cleaning solution, wiping technique, storage temperature range or drop rating for the end cap. It also does not confirm whether the cap fits filter systems other than the F:X Pro Magnetic Round Filters Mark II. Those gaps are decision limits, not product faults: if you need a specific cleaning method or a hard case, that information is not confirmed here and should be checked separately.

For the end cap itself, the practical takeaway is narrow and useful. Match the diameter, use it to close a Mark II filter stack in transit, and pull it off before mounting the filters on the lens.

مقالات ذات صلة

Customer Service
الرئيسية
المنتجات
السلة
الملف الشخصي